Widebody 86 / BRZ / GR86 Wheel Fitment: Rocket Bunny, Pandem & 5x100 Offsets

HausofWheels own photo of WORK Emotion GT6 3P Silver extreme widebody-spec 5x100 wheels; product reference, not shown on a vehicle

What wheels fit a widebody Toyota 86, Subaru BRZ or GR86? Start with the exact body-kit version and the measured front and rear arch space—not a single “perfect” offset copied from another build. The original ZN6/ZC6 coupe and newer ZN8/ZD8 GR86/BRZ both normally use 5x100 PCD, but the available clearance, factory wheel baseline and widebody flare dimensions differ. An aggressive-looking 18x10 or negative-offset wheel is not automatically suitable for every Rocket Bunny or Pandem kit.

This Australian guide compares documented Rocket Bunny/Pandem fender widths, explains genuine JDM wheel-position arithmetic, and shows actual HausofWheels 5x100 wheel specifications. It does not claim we have physically tested these wheels on a particular widebody car.

Rocket Bunny/Pandem widebody 86 and GR86: which kit do you have?

First identify the chassis and exact kit part number. These are manufacturer-listed extensions per side for particular versions, measured relative to the original body; they are not an automatic wheel-offset recommendation.

Kit / chassis Front flare width Rear flare width Manufacturer reference
GReddy / Rocket Bunny ZN6 original wide version +40 mm per side +65 mm per side GReddy/Trust original ZN6 wide-version components
Rocket Bunny ZN6/ZC6 Version 2, part 17010225 +45 mm per side +70 mm per side GReddy V2 component specifications
Pandem GR86 ZN8 V1/V1.5, 2022+ +65 mm per side +85 mm per side GReddy Pandem GR86 kit specification

Other authentic kit versions, replica kits, custom overfenders and hand-finished installations can have different widths and mounting lines. Some product variants are specific to pre-facelift ZN6 body panels. Do not treat a ZN6 kit as interchangeable with a ZN8/ZD8 kit, or assume GR86 and BRZ front-bumper pieces are interchangeable. Verify the actual purchased kit with its producer or body shop.

Why +65 mm overfenders do not mean you need 65 mm of extra wheel poke

The factory wheel may sit considerably inward of the original guard, and the widebody panel may change the arch opening as well as the outer edge. A +65 mm panel does not instruct you to move the rim +65 mm, and a wider tyre can extend beyond the bare wheel rim. The correct target is the measured tyre-and-wheel envelope under your installed flares, with enough movement clearance for suspension compression and full steering lock.

First check whether the car has factory struts, lowered springs, coilovers, air suspension or modified lower arms; measure camber, ride height and wheel-to-strut clearance. Then confirm your planned tyre's section width and shoulder shape on its approved rim width. Cutting original guards and resealing exposed metal may be necessary for certain widebody kits. GReddy/Pandem specifically warns that its GR86 kit requires body cutting and inner-fender sealing.

Wheel size and offset examples: 18x9.5 +38, 18x10 +38 and negative offsets

The figures below are nominal rim-position calculations from two factory-style benchmarks, not proof of wheel-to-body or brake fitment. For a first-generation 86/BRZ, use an example 17x7 +48 reference (common on non-Brembo ZN6/ZC6 grades). For a 2022+ GR86/BRZ, use an example 18x7.5 +48 reference. Your car may have a different factory wheel. The offset is measured in millimetres.

Example aftermarket wheel Outer rim farther out vs ZN6 17x7 +48 Outer rim farther out vs ZN8 18x7.5 +48
18x9.5 +38, 5x100 41.8 mm 35.4 mm
18x10 +38, 5x100 48.1 mm 41.8 mm
18x9.5 -13, 5x100 92.8 mm 86.4 mm
18x10.5 -25, 5x100 117.5 mm 111.1 mm

How it is calculated: outward change = half of the rim-width increase (in mm) + the reduction in offset. Inward change = half the width increase − the reduction in offset. For example, compared with ZN6 17x7 +48, a 9.5-inch +38 wheel adds (2.5 × 25.4)/2 + 10 = 41.75 mm outward and brings the inner rim 21.75 mm closer to the suspension. A 10-inch +38 wheel adds 48.1 mm outward and brings the inner rim 28.1 mm closer.

The negative-offset examples are radically more outward: relative to ZN6 17x7 +48, 18x9.5 -13 moves the inner rim roughly 29.3 mm farther from the suspension while moving the outer lip about 92.8 mm outward; 18x10.5 -25 moves the inner rim roughly 28.6 mm farther from the suspension but the outer rim about 117.5 mm outward. These dimensions may exceed the useful envelope of some widebody kits. They must not be treated as suitable simply because the wheel listing says “widebody”.

Genuine 5x100 JDM wheels to compare for a widebody build

The following are real HausofWheels catalogue examples of width, offset and construction. Confirm the product's current price, condition and stock status on its live listing. None is presented as pre-approved for an unmeasured Rocket Bunny or Pandem conversion.

HausofWheels own photo: RAYS Gram Lights 57DR Bronze 18x9.5 +38, 5x100 wheel, not installed on a widebody car

RAYS 57DR Bronze — 18x9.5 +38

5x100 square-set geometry to compare before measuring outer guards, tyres and inner suspension. Check current stock on the listing.

HausofWheels own photo: WORK Emotion GT5 Matte Black 18x10 +38, 5x100; wheel photo only

WORK GT5 Matte Black — 18x10 +38

Wider 5x100 specification. Verify tyre manufacturer fitment, hub, caliper clearance and suspension/guard movement.

Another three-piece option for comparing construction and disc clearance is SSR Professor SP1 Silver — 18x9.5 +37, 5x100. The WORK Emotion GT6 3P Silver — 18x9.5 -13 front / 18x10.5 -25 rear is a sold-out reference listing illustrating how extreme dedicated widebody specifications can become; it is not a currently available set or a universal fitment recommendation. Do not assume that every kit needs these negative offsets.

Compare the broader 18-inch 5x100 wheel collection, all 5x100 JDM wheels and Sydney-stock wheel sets. Confirm the actual specification rather than relying on a model-level representative photograph.

Does a widebody kit change the PCD or brake clearance?

No. Installing wider fenders does not change the factory 5x100 bolt pattern, nominal 56.1 mm hub bore or the required wheel-nut thread for an unconverted 86/BRZ hub. PCD conversions and spacer/adaptor systems are separate modifications, and wheels advertised as 5x114.3 should not be considered direct-fit replacements for a 5x100 hub. Never assume an adaptor makes an unsafe brake, load or legal configuration acceptable.

Body clearance and caliper clearance are different. Factory Brembo-equipped Toyota 86/BRZ grades, GR86/BRZ tS variants and aftermarket brake kits may require particular spoke profiles and barrels. Ask for wheel-specific brake templates, actual caliper measurements and the exact wheel disc type where applicable. See our GR86/BRZ Brembo clearance guide and wheel/brake-caliper clearance explanation.

Tyre size, stretching and suspension: why the wheel-only calculation is not enough

Do not choose a narrow tyre merely to force an extreme wheel inside a flare. Tyres must be compatible with the wheel's approved width range, have suitable load and speed ratings, maintain the required rolling diameter and remain clear throughout suspension travel and steering. Alignment, camber, ride height, front wheel lock, rear bumper-tab position and arch-liner modifications all affect the result. If the build is used on a public road in Australia, assess these choices for safety and applicable state requirements before installation.

NSW guidance distinguishes minor from significant modifications; body, wheel, tyre and suspension changes may require assessment and a certificate from an appropriately licensed certifier. Check your state or territory's rules before cutting panels or buying extreme-offset wheels. See the NSW modified-vehicle requirements and the Australian Government's VSB 14 technical standards.

How to measure your widebody 86/BRZ before ordering wheels

  1. Identify the chassis and kit: Toyota 86 ZN6 / Subaru BRZ ZC6 or Toyota GR86 ZN8 / Subaru BRZ ZD8; manufacturer, kit version, panel finish and measured fender edges.
  2. Document the current wheels: front and rear diameter, width, offset, tyre brand/size, hub specification and any spacers or PCD conversions.
  3. Measure at intended ride height: hub face to outer permissible tyre/fender envelope, inner coilover/spring clearance, steering lock and suspension bump travel.
  4. Verify the brakes: original or upgraded calipers, rotor size, wheel model/disc, and independent barrel/spoke clearance.
  5. Choose a tyre and wheel combination: check tyre manufacturer's approved rim width and the actual section width of the proposed tyre.
  6. Arrange professional compliance and fitting checks: assess body cutting, corrosion protection, sealing, guard coverage, roadworthiness and certification requirements.

Widebody fitment FAQ

Will a Rocket Bunny V2 widebody ZN6 fit the same wheels as a Pandem GR86?

Not automatically. Their published panel extensions differ, their chassis reference wheel positions differ, and each installed car's suspension/tyres/body finishing may be unique. Measure both front and rear on the actual build.

Do I need 18x11 or a negative offset for a widebody 86?

No fixed width or negative offset is mandatory simply because a car has flares. Some widebody builds use extreme wheels and substantial supporting modifications; others can fill their arches with a more positive offset depending on track width and tyre choice. Selecting by appearance alone risks excessive poke or suspension/body interference.

Can I order wheels for the kit before the bodywork is installed?

You can plan candidate dimensions from the kit documentation, but the final order should follow measurements on the assembled body and suspension. Kit flares are not a substitute for a fitment test, and wheel design affects brake clearance independently of offset.

Where can I compare standard-body fitments first?

Read our first-generation ZN6/ZC6 fitment guide, second-generation GR86/BRZ guide and GR86 18x8.5 +45 versus 18x9.5 +38 comparison. These are standard/modified-car starting points, not widebody kit approvals.

Ask HausofWheels about genuine wheels for your widebody build

Send a wheel-fitment enquiry with the kit name/version, chassis, actual front/rear measured clearance, brakes, suspension, intended tyres and desired finish. We supply genuine RAYS, WORK, SSR and other JDM wheels, including selected 5x100 sizes. We do not sell tyres or provide physical fitting, bodywork or modification certification. Hurstville pickup is by confirmed appointment once an eligible wheel order is ready.

Sources and editorial method

The kit sizes are quoted from linked GReddy ZN6 original wide-version, GReddy ZN6 V2 and GReddy Pandem ZN8 specifications. Factory wheel starting points were checked with Japanese-market ZN6 factory wheel tables and 2022+ GR86/BRZ specialist measured fitment notes. Wheel-position values are original arithmetic for illustrative benchmarks; actual clearances must be physically verified. This guide was prepared using research and existing HausofWheels product specifications, not hands-on testing of each body kit.

Back to blog

Genuine wheel fitment

Find the right wheels for your car

Browse genuine wheels currently available to order, then use our fitment guides to narrow down PCD, size and offset for your exact vehicle.

Need help applying this guide to your car? Ask HausofWheels about this fitment guide →